Frequently Asked Questions¶
How do I know if watchmaker has installed?¶
To determine whether watchmaker is installed, the simplest method is to run the
watchmaker --help. If it displays the cli help page, watchmaker is
installed. Another option is to check
pip list | grep watchmaker.
What do I do if watchmaker failed to install?¶
First, review the installation document. Then double-check the output of a failed installation. Usually, the output points pretty clearly at the source of the problem. Watchmaker can be re-installed over itself with no problem, so once the root cause is resolved, simply re-install watchmaker.
Why does the watchmaker install fail if my system is FIPS enabled?¶
This is primarily a question for Red Hat (and derived distributions). As of this
pip utility in all Red Hat releases up through 7.4.1708, default
to looking for pypi packages signed with MD5 signatures. If you’ve enabled FIPS
(or are using a build that has FIPS pre-enabled), MD5 is disabled in the kernel
(due to being a weak hashing-method). You can either disable FIPS (not
recommended) or explicitly force
pip to use a different signature-index. The
latter is detailed in the Linux section of the usage document.
How do I know if watchmaker has completed without errors?¶
By default, watchmaker will reboot the system after a sucessful execution.
Therefore, if the system reboots, watchmaker executed successfully. If you are
investigating sometime after watchmaker completed, check the logs for errors.
If anything fails, watchmaker will suppress the reboot. (Though note that the
--no-reboot flag can be used to suppress the reboot even after a successful
You can also test the watchmaker exit code programmatically. If watchmaker
fails, it will return a non-zero exit code. If watchmaker completes
successfully, it will return an exit code of zero. You would typically pass the
--no-reboot flag if you intend to test the exit code and determine what to do
What do I do if watchmaker failed to complete or completes with errors?¶
Start by checking the logs generated by watchmaker. The logs are stored in the
directory specified by the
--log-dir argument. Search the log for entries
[ERROR], this will give you a starting point to begin
troubleshooting. Also, if a salt state failed, look for the pattern
Result: False. If it is not an obvious or simple issue, feel free to create
an issue on the watchmaker github page. If there is a salt_call.debug.log in
the watchmaker log directory, you can look for
[ERROR] messages in there as
well. However, this log file can be very noisy and a message with the error
label may not be related to the error you are encountering.
Does watchmaker support Enterprise Linux 7?¶
Watchmaker is supported on RedHat 7 and CentOS 7. See the index page for a list of all supported operating systems.
How can I exclude salt states when executing watchmaker?¶
The Salt worker in Watchmaker supports an
exclude_states argument. When
present, the value is passed directly to the
exclude option of the
salt highstate execution module.
To use this option with watchmaker from the command line, pass the argument
--exclude-states <sls_glob>. For example:
# Exclude the state "foo" with an exact match watchmaker --exclude-states foo # Exclude all state names that begin with "foo" watchmaker --exclude-states foo* # Exclude multiple states "foo" and "bar" with an exact match watchmaker --exclude-states foo,bar
Can I use the underlying salt functionality directly?¶
Yes, by passing watchmaker’s salt configuration directory to the salt command,
# -c|--config-dir salt-call -c /opt/watchmaker/salt state.show_top
Can I use watchmaker to toggle my RedHat/Centos host’s FIPS mode?¶
Yes, indirectly. Because watchmaker implements most of its functionality via SaltStack modules, you can directly-use the underlying SaltStack functionality to effect the desired change. This is done from the commandline - as root - by executing:
salt-call -c /opt/watchmaker/salt ash.fips_disable
salt-call -c /opt/watchmaker/salt ash.fips_enable
And then rebooting the system.
How do I install watchmaker when I am using Python 2.6?¶
While Watchmaker no longer offically supports Python 2.6, you may use the last version where it was tested, Watchmaker 0.21.7. That version includes pins on dependencies that will work for Python 2.6.
However, there are three python “setup” packages needed just to install
and these packages cannot be platform-restricted within the
Below is the list of packages in question, and the versions that no longer support Python 2.6:
In order to install pip in Python 2.6, you can get it from:
Once a Python 2.6-compatible
pip version is installed, you can install
compatible versions of the other packages like this:
python -m pip install --upgrade "pip<10" "wheel<0.30.0" "setuptools<37"
You can then install watchmaker by restricting the watchmaker version to the last version tested with Python 2.6:
python -m pip install "watchmaker==0.21.7"
How do I get Watchmaker release/project notifications?¶
Users may use an RSS reader of their choice to subscribe to the Watchmaker Release feed to get notifications on Watchmaker releases. The Watchmaker RSS release feed is https://github.com/plus3it/watchmaker/releases.atom.
Users can also “watch” the GitHub project to receive notifications on all project activity, https://github.com/plus3it/watchmaker/subscription.